Poison-spyder WHEEL SPACERS Manuel d'utilisateur télécharger pdf

INSTALLATION INSTRUCTIONS

WHEEL SPACERS INSTALLATION INSTRUCTIONS

Thank you for purchasing a pair of Poison Spyder

Wheel Spacers. Installation is fairly simple with

the right tools and good mechanical abilities. If

you are not condent in your mechanical skills,

please seek the help of a professional to perform

the installation. Please read through these entire

instructions before proceeding with installation.

TOOLS NEEDED

• FloorJack&JackStand

• Lug Nut Wrench or Socket, Ratchet &

Extension

• WireBrush

• TorqueWrench

INSTALLATION PROCEDURE

1. Park vehicle on a level surfaceandsetthe

parkingbrake.Placewheelblockorchockat

frontwheel(oppositetheoneyou’reworking

on,ifinstallingspacersonthefrontwheels).

Youwillwanttoweareyeprotectionbeyond

thispointintime.

2. Use the oor jack to lift the wheel of the

ground,placeaxleonjackstandandremove

oorjack.DO NOT work on the vehicle with

only the jack holding it up!

3. Use a wire brush to cleansurface ofhub/

rotor or drum where the spacer is going

to be mounted.  Surface must be clean so

thatthespacersitsperfectlyatagainstthe

mountingsurface.Insomevehiclemodels,

rotorretainerclipsmustberemovedtoallow

thespacertositat.

4. Install the spacer using the supplied lug

nuts, nger-tight.  These “bulge” style lug

nutsaredesignedforthetaperedendtoseat

intothemachinedtaperedholeinthespacer.

5. Using a calibrated torque wrench, dry

torque the lug nuts in a star pattern to

your vehicle manufacturer’s specications

(check your owner’s manual for dry torque

specications).DO NOTUSEAN IMPACT

GUN,asitmaydamagethelugnutsand/or

studs.

6. Once the spacer is installed, check the

surface of the spacer.  Studs or lug nuts

should not protrude beyond the wheel

mounting surface of the spacer.  Using a

straight-edge along the wheel mounting

surfacemaybehelpfulifitlooks“close”.

7. Install wheel using the same lugnutsthat

were originally removed.  The threads on

the lug nuts MUST match the threads on

the wheel spacer!  If yours do not match,

stop this installation and contact Poison

Spyder.  Do not cross-thread or force mis-

matched threads! Usea torquewrench,in

astarpattern,totightenthelugnutstothe

manufacturer’sspecication.

8. Use oor jack to lift wheel, remove jack

stand,andsetwheelontheground.Repeat

theinstallprocedurefortheoppositewheel.

9. After both wheel spacers are installed,

drivethevehicle for 10miles. Then, using

theprocedureoutlinedabove,removeeach

wheeland checkthe torqueof thelug nuts

holdingthespacertothehub.Ifre-torquing

isneeded,dosothenrepeatthe10-miletest

drive and re-check.  Repeat the re-torque/

testdrive/re-checkprocedureuntilnofurther

re-torquingisneeded.

10. After 100 miles, remove the wheel and

checkthetorqueonceagain,andre-torque/

re-checkasneeded.

Congratulations, you have completed installation

of your Poison Spyder Wheel Spacers.

1 2

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Page 2

Commentaires sur ces manuels

Pas de commentaire

Poison-spyder WHEEL SPACERS Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Poison-spyder WHEEL SPACERS. Poison Spyder WHEEL SPACERS User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Poison-spyder WHEEL SPACERS