Poison-spyder TJ REAR BUMPER BRACE KIT Manuel d'utilisateur télécharger pdf

INSTALLATION INSTRUCTIONS

©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM

The Poison Spyder Customs TJ Rear Bumper

Brace Kit is easy to install with the right tools

and good mechanical abilities. If you are not

condent in your mechanical skills, please

seek the help of a professional to perform the

installation. Please read through these entire

instructions before proceeding with installation.

PARTS LIST

(1) TJ Rear Bumper Brace, Left

(1) TJ Rear Bumper Brace, Right

(2) Nut Plate

(4) 7/16-14 X 1 Gr8 Hex Head Cap Screw

(4) 7/16 Split Lock Washer

(4) 7/16 Flat Washer

TOOLS NEEDED

• Primer, paint, cleaners and masking

materials (if painting)

• 5/8” socket & ratchet

• Torque wrench

• Soft dead blow hammer or rubber mallet

BEFORE YOU BEGIN

IMPORTANT: The Poison Spyder Customs TJ

Rear Bumper Brace Kit comes as unpainted,

bare steel. You will want to either powder coat

or paint the bumper prior to nal installation,

however it is recommended to completely install

and remove the bumper prior to painting or

powder coating it. This will allow you to check

for tment or do any clearancing or tting ahead

of time, to reduce the chance of damage to the

nish during nal installation. Poison Spyder

Customs Inc. is not responsible for costs for or

damage to paint or powder coat nish under any

circumstances, including paint or powder coat of

incorrectly shipped or defective parts.

INSTALLATION PROCEDURE

NOTE: It is assumed that this item is being

installed in conjunction with a Poison Spyder or

other manufacturer’s aftermarket bumper, that

the OE bumper has already been removed, and

that the replacement bumper has already been

“dry t” and ready to install.

1. Park the Jeep on a at, level surface and

set the parking brake.

2. With the bumper partially installed on to

the Jeep (mounting bolts slipped through the

holes in the Jeep’s rear crossmember, but

nuts not yet installed), temporarily install the

Rear Bumper Braces. Note that the braces

areinleftandrightcongurations,sometest-

ttingmaybenecessarytodeterminewhich

one goes on each side. When properly

placed, the opposing holes in the frame rail

side of the Brace will align with existing holes

in the side of the Jeep’s frame rails. Secure

the Braces in place by installing the nuts that

came with the bumper, but do not fully tighten

them at this time.

3. Find the existing elongated hole located

along the bottom surface of the frame rail

on each side, below the frame rail side bolt

lcations for the Braces. Insert one of the

provided nut plates through this hole, and

slide it up toward the bolt holes, with the

at side of the nut plate against the inside

surface of the frame rail.

4. Insert a 7/16-14 Gr8 Hex Head Cap Screw

through a 7/16 Split Lock Washer and 7/16

Flat Washer, then through each hole in the

Brace and frame rail, and thread into the Nut

Plate inside the frame rail. Do this for both

hole locations on each side.

TJ REAR BUMPER BRACE KIT INSTALLATION

1 2 3

INSTALLATION INSTRUCTIONS 1

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COMThe Poison Spyder Customs TJ Rear Bumper Brace Kit is

Page 2

INSTALLATION INSTRUCTIONS©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COMPoison Spyder Customs • TJ REAR BUMPER BRACE KIT Page

Page 3

INSTALLATION INSTRUCTIONS©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COMPoison Spyder Customs • TJ REAR BUMPER BRACE KIT Page

Commentaires sur ces manuels

Pas de commentaire